Under Crank Shearing Machine

Features:

• Front Gauge: T-Slotted fron gauge fabricated from mild steel is detachable. 
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade:Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication:All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.
• Standard Equipments:Rear gauge, Side squaring and Front gauge, Foot pedal, Switch Motor pulley, Gear & Fly wheel guards and standard. Interaction manual, and Spanner.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.

• Frame: The Frame is fabricated from steel plates of is 226 Grade. The frame is designed to take heavy loads. The interlocked design put the direct support to frame. Thus frame is strain free and eliminates welds at load supports. Thus the Accuracy of The Machine is never disturbed.
• Table: Steel fabricated, box type table is heavily ribbed for strength and is stress relieved its machined seat provides true and firm support to the bottom blade. It is adjustably for setting the blade clearance. The top surface of the table is provided with T slots for adjusting the front gurge.
• Upper Beam:Upper beam is fabricated with thick M.S. Plate. It is Heavily ribbed from behind and is stress relived. The top blade is fitted at its accurately machined seat. Its sliding surface are machined and hand scrapped for smooth travel and sustained accurately.
• Guide Ways:Accurately machined guide ways keep the beam in its bearing throughout the stroke. A taper wedge is provide to compensate for the wear and to facilitate quick setting of the blade clearance.
• Hold Down Device: The spring loaded mechanical hold down pads hold the sheet securely, to avoid slipping and bowing resulting in clean square cuts. Hold down units are provided with oversize pads to avoid impressions on sheet metal on request.
• Drive: Motor, mounted on an adjustable platform, drives the large, cast iron fly wheel through v-belts. The power is Further transmitted to the fly wheel shaft through steel pinion and main gear box and than transmitted to main gear. Gun-Metal bushes are provided all the rotating parts .
• Clutch: Rollin key clutch is linked with the main gear and engages every time when the foot switch is pressed.
• Brake: Spring tensioned braked fitted at the end of the crank shift to damp inertia.
• Front Gauge: T-Slotted front gauge fabricated from mild steel is detachable.
• Rear Gauge: Rack and Pinion type rear gauge provides accuracy and is easily adjustable to parallel and taper strips efficiently.
• Blade: Everest shears are provided with high quality single or segment HCHCR blade, with four edged.
• Lubrication: All bearing parts and guide surfaces are lubricated through connected oil cups and operated lubrication pump.

• Electric items & blades are not under warranty.
• Machines will be supplied without electricals & V-belts.